Activity Stream - Scream And Fly Powerboat and High Performance Powerboating Discussion Forums (2024)

New Activity ()

Please reload this page to view the 200+ new activity items that have been created.

• Older Activity

• 

  Today,12:10 AM

  Baker343 replied to a thread Upcoming Event: 2024 Parker Enduro in General Boating Discussion

  The first Rampage out of the mold, running the Parker Enduro with a hopped up Rude in I think 1987.

  see more

  9 replies | 511 view(s)

• 

  Yesterday,11:02 PM

  tlwjkw replied to a thread 2001 mercury 200 efi on firing on #1 cylinder in Technical Discussion

  gonna be more than a switch box more than likely then.... i'm not confident enough ta suggest anything to do for it on tha computer.. it may get a...

  see more

  25 replies | 260 view(s)

• 

  Yesterday,10:45 PM

  200valeroyt replied to a thread 2001 mercury 200 efi on firing on #1 cylinder in Technical Discussion

  It’s not firing on 5 cylinders

  see more

  25 replies | 260 view(s)

• 

  Yesterday,10:39 PM

  tlwjkw replied to a thread Fuel pressure on a carburetor v-6 in Technical Discussion

  :thumbsup: have some friends run as low as 3lbs (bone stock 2.4's/2.5's) without problems.. so there's that!

  see more

  4 replies | 91 view(s)

• 

  See Also

  Activity Stream - Scream And Fly Powerboat and High Performance Powerboating Discussion ForumsThe Rite of Spring: Concert and Dance - The Japan Foundation, BangkokYamaha Racing Snowshoe: ATV Race Report - GNCC RacingT 0153/22 22-04-2024 | Epo.org

  Yesterday,10:30 PM

  tlwjkw replied to a thread 2001 mercury 200 efi on firing on #1 cylinder in Technical Discussion

  i may be missing something??? is tha motor NOT FIRING ON ONE cylinder OR is it NOT FIRING ON FIVE cylinders??? if its not firing on FIVE cylinders...

  see more

  25 replies | 260 view(s)

• 

  Yesterday,10:22 PM

  skialot2 started a thread Video: Watching lower unit while running in General Boating Discussion

  Had the camera set to see the prop also but the camera moved. Can only see the nose cone.

  see more

  0 replies | 31 view(s)

• 

  Yesterday,10:11 PM

  Onetime replied to a thread Attwood Ballistic Prop Boxes in Propellers

  Sent you a pm this morning

  see more

  4 replies | 272 view(s)

• 

  Yesterday,09:56 PM

  skialot2 replied to a thread Surface running props in Props, Setup, and Rigging

  Suspicion confirmed!!! Tachometer is off by a hundred or two at idol and about 1400-1500 RPMs at full throttle. I installed a tachometer for small...

  see more

  39 replies | 1449 view(s)

• 

  Yesterday,09:42 PM

  Thefakeseanryan started a thread 21 Superboat CC 2009 in Hulls larger than 20'

  2009 21 Superboat center console. 2023 mercury 250 ProXS w/ about 35-40 hours All new rigging and wiring power steering Bobs 4” hydraulic...

  see more

  0 replies | 55 view(s)

• 

  Yesterday,09:38 PM

  wogi replied to a thread Fuel pressure on a carburetor v-6 in Technical Discussion

  See Also

  Headline news on March 11, 2009

  Thanks, I was thinking 4to6 psi, just wanted to know what others have been running. I was thinking that more than 7 may blow the needles off the...

  see more

  4 replies | 91 view(s)

• 

  Yesterday,09:17 PM

  skialot2 replied to a thread Picked up 3 V6 Mercs today... For parts? in General Boating Discussion

  Well, I just couldn't help myself. I picked up another motor. $150. Boat sank. They said water only made it in the bottom carb. Powerhead is...

  see more

  9 replies | 398 view(s)

• 

  Yesterday,09:03 PM

  200valeroyt replied to a thread 2001 mercury 200 efi on firing on #1 cylinder in Technical Discussion

  I replied through the same email. I thought I may have been on to something with one of the switch boxes looked dark and burnt on one side through...

  see more

  25 replies | 260 view(s)

• 

  Yesterday,08:45 PM

  tlwjkw replied to a thread Fuel pressure on a carburetor v-6 in Technical Discussion

  ran 6 ta 7/8 on our BP's, oval ports (20's, 22's 46's) and 245's (wmv's with and without pumps) no problems but 90% of run time was with both feet on...

  see more

  4 replies | 91 view(s)

• 

  Yesterday,08:18 PM

  oldschoolnc started a thread GT200 Identification confirmation help please in Technical Discussion

  Johnson 200 identification What is a J200STLENS? It has a GT200 hood on it. It's a 20" lower. I think it's a 92 model. Ser.#003021654... It...

  see more

  0 replies | 18 view(s)

• 

  Yesterday,07:56 PM

  Instigator started a thread Never seen one! in Ebay Listings and Other Internet Listings

  Very cool pc of history. https://www.facebook.com/marketplace/item/816997663695014/?ref=search

  see more

  0 replies | 36 view(s)

• 

  Yesterday,07:28 PM

  skialot2 replied to a thread Fuel pressure on a carburetor v-6 in Technical Discussion

  I believe 4-6 psi is correct for just about all carb motors. Any more and you can push the needle off the seat.

  see more

  4 replies | 91 view(s)

• 

  Yesterday,07:13 PM

  tlwjkw replied to a thread 2001 mercury 200 efi on firing on #1 cylinder in Technical Discussion

  didn't get it?

  see more

  25 replies | 260 view(s)

• 

  Yesterday,07:08 PM

  Shemp started a thread Smurf Blue Frankenrude triple in Technical Discussion

  Hi all. picked up a redneck special OMC triple. I believe is a 1990 or 1991 56 Cube, based on part numbers. Motor ID decal was sanded off ,...

  see more

  0 replies | 39 view(s)

• 

  Yesterday,06:35 PM

  Mark Poole ModVP replied to a thread Mercury Through The Years... in Outboard and Racing History

  They were doing some cool things in unlimited until most of the teams decided to go turbine power.

  see more

  27945 replies | 3310944 view(s)

Image resizer by SevenSkins